Author |
Message |
gblair Samba Member
Joined: September 07, 2013 Posts: 159
|
Posted: Sat Sep 06, 2014 5:42 pm Post subject: Cricket in my Thing |
|
|
HI
I have a sound that is driving me nuts(not far to get there). Had my wife pushing on my rear bumper and I could see the bolt attaching the rear shock mount(not sure if that is what that is called) to the body of the car moving. I tried to tighten it and could not get it to budge. I think if I used an impact it might tighten. Is that a good idea or do these have a tendency to brake off?
Any ideas on what I should do?
Thank
[/img] |
|
Back to top |
|
|
GI Joe Samba Member
Joined: April 28, 2005 Posts: 2012 Location: Athens, TN
|
Posted: Sat Sep 06, 2014 8:00 pm Post subject: |
|
|
That is one of the rear body bolts... So, actually your body is bolted to the shock mount.. Anyway,
I would Not hit it with an impact.... Give it a few soak cycles with your favorite penetrating fluid and then try again with a socket.. Also, a quicker fix may be to just spray some silicone lube onto that rubber bushing sandwiched between the body and shock mount.. It's probably pretty dry and is chirping between the metal..
I spray all the rubber bushings I can find on All my cars, as chirps and squeaks drive me nuts!!
Good luck! _________________ '74 Thing, "Our Thing"....
http://www.thesamba.com/vw/forum/viewtopic.php?t=4...p;start=60
'71 Beetle RPU
http://www.thesamba.com/vw/forum/viewtopic.php?p=8080337#8080337
www.NLEOMF.com
Respect, Honor, Remember |
|
Back to top |
|
|
saddlesore1 Samba Member
Joined: November 20, 2006 Posts: 548
|
Posted: Mon Sep 08, 2014 2:25 pm Post subject: |
|
|
I have found a good torch will brake up what ever is bonding it. If you get the head of the bolt close to glowing, let it cool down a bit then put a wrench on it might get it to move. |
|
Back to top |
|
|
gblair Samba Member
Joined: September 07, 2013 Posts: 159
|
Posted: Mon Sep 08, 2014 5:44 pm Post subject: |
|
|
Would anyone know where to get the rubber buffer 111-799-119 (find item 3 in the parts manual page 172) These are hard as rocks and if I get them loose I would like to just replace them? |
|
Back to top |
|
|
brooklyn thing Samba Member
Joined: April 01, 2011 Posts: 98 Location: brooklyn
|
Posted: Mon Sep 08, 2014 5:51 pm Post subject: |
|
|
Hmm.....I would be very careful about trying to turn those bolts. Don't you risk breaking the welds that hold the nut? Aren't the nuts inaccessible without cutting a hole in the body? I mention this because one of mine broke free and the bolt just spins. I was thinking of cutting the rubber out, cut a groove in a slightly larger rubber washer and force them into place with the body jacked up slightly. |
|
Back to top |
|
|
kubelmann Samba Member
Joined: April 13, 2003 Posts: 3266
|
Posted: Tue Sep 09, 2014 3:51 am Post subject: |
|
|
These body pads are a common VW part and not Thing specific. The mounting hardware on the other hand is Thing only and should be soaked with PB Blaster of other rust penetrant. If I was removing those bolts I would do it over the period of a week.. First heat slightly and then spray PB blaster. I would start by trying to ever so slightly tighten then loosen the bolt. I would mover apply much pressure. Just keep working toward that free movement with no force.. When these bolts break that are a pan to repair. Ask me how I know. . It is way easier to take your time and get the bolt out. If you are patient and take your time, every bolt will come out. The minute you put your back into it, usually a bolt breaks. Each side originally had two pads.. They slide on the steel bushing that goes on the body bolt. The center section of the Thing’s body bolts solidly to the pan. The front and rear of the body bolts with rubber pads to the rear torsion arm assembly and the front beam as suspension shock mounts.. The factory Thing manual says pn 111799 119 The Thing shop sells 111 899 115A This part is important to get OE and the rubber needs to be pliable. If you install an aftermarket (stiff rubber) the pad will crack and break within less than year. Ask me how I know.. West Coast Metric (and others have the “real” part... Do not be fooled. CSP have the original part for under $3:
http://www.csp-shop.com/cgi-bin/cshop2/front/shop_main.cgi?func=detail&artnr=12370c |
|
Back to top |
|
|
|